Sequestration of Pb(II) using channel-like porous spheres of carboxylated graphene oxide-incorporated cellulose acetate@iminodiacetic acid: optimization and mechanism study.

The adsorption property of the costless green cellulose acetate (CA) was boosted by the dual modifications: inner modification by incorporating carboxylated graphene oxide (COOH-GO) into the CA spheres and outer modification by the surface modification of the COOH-GO@CA spheres by iminodiacetic acid (IDA) for removing Pb(II). The adsorption experiments of the Pb(II) proceeded in a batch mode to evaluate the adsorption property of the COOH-GO@CA@IDA spheres. The maximal Pb(II) adsorption capacity attained 613.30 mg/g within 90 min at pH = 5. The removal of Pb(II) reached its equilibrium within 20 min, and the removal % was almost 100% after 30 min at the low Pb(II) concentration. The Pb(II) adsorption mechanism was proposed according to the kinetics and isotherms studies; in addition, the zeta potential (ZP) measurements and X-ray Photoelectron Spectroscopy (XPS) analysis defined the adsorption pathways. By comparing the XPS spectra of the authentic and used COOH-GO@CA@IDA, it was deduced that the contributed chemical adsorption pathways are Lewis acid-base, precipitation, and complexation. The zeta potential (ZP) measurements demonstrated the electrostatic interaction participation in adsorbing the cationic Pb(II) species onto the negatively charged spheres (ZP = 14.2 mV at pH = 5). The unique channel-like pores of the COOH-GO@CA@IDA spheres suggested the pore-filling mechanism of Pb(II). The promising adsorption results and the superb recyclability character of COOH-GO@CA@IDA enable it to extend of the bench scale to the industrial scale.

Cellulose acetate nanofiber modified with polydopamine polymerized MOFs for efficient removal of noxious organic dyes.

The need to effectively remove toxic organic dyes from aquatic systems has become an increasingly critical issue in the recent years. In pursuit of this objective, polydopamine (PDA)-binary ZIF-8/UiO-66 (MOFs) was synthesized and incorporated into cellulose acetate (CA), producing ZIF-8/UiO-66/PDA@CA composite nanofibers under meticulously optimized conditions. The potential of fabricated nanofibers to remove cationic methylene blue (MB) dye was investigated. Various analysis tools including FTIR, XRD, SEM, zeta potential, BET, tensile strength testing, and XPS were employed. Results revealed a substantial leap in tensile strength, with ZIF-8/UiO-66/PDA@CA registering an impressive 2.8 MPa, as a marked improvement over the neat CA nanofibers (1.1 MPa). ZIF-8/UiO-66/PDA@CA nanofibers exhibit an outstanding adsorption capacity of 82 mg/g, notably outperforming the 22.4 mg/g capacity of neat CA nanofibers. In binary dye systems, these nanofibers exhibit a striking maximum adsorption capacity of 108 mg/g, establishing their eminence in addressing the complexities of wastewater treatment. Furthermore, the adsorption data fitted to the Langmuir isotherm, and the pseudo-second-order kinetic model. The fabricated nanofiber demonstrates good reproducibility and durability, consistently upholding its performance over five cycles. This suite of remarkable attributes collectively underscores its potential as a robust, durable, and highly promising solution for the effective and efficient removal of pernicious MB dye, in the context of both water quality improvement and environmental preservation.

Development of novel amino-ethyl chitosan hydrogel for the removal of methyl orange azo dye model.

The present study introduces a new and straightforward method for the amination of Chitosan. This method involves coupling Chitosan (CS) with 2-chloroethylamine (ENH2) in a single step to produce an amino-ethyl Chitosan derivatives with increased amine group content (CS-ENH2) using click chemistry. The resulting derivatives were then crosslinked using Glutaraldehyde to form amino-ethyl Chitosan Schiff bases. The novel amino-ethyl Chitosan Schiff bases were subsequently utilized as adsorbents for the removal of Methyl Orange (MO) dye from aqueous solutions using a batch technique, and the performance of the produced Schiff bases was compared with that of the native Chitosan Schiff base. The CS-ENH2 adsorbents show improved adsorption capacity up to 300% of the native Chitosan Schiff base with almost double removal rate. The adsorption temperature has a positive impact in general while almost 100% of MO removed at 60 °C using CS-ENH2 adsorbents compared with 66% of the native Chitosan Schiff base adsorbent. The adsorption pH shows a negative impact on the MO removal percent. That effect reduced sharply using the CS-ENH2 adsorbents with higher amination degree while the MO removal percent almost being constant over a wide range of pH; 2.0-7.0. The agitation speed has the same positive effect over all the adsorbents. However, the rate of MO removal percent decreased with increase the agitation speed up to 250 rpm. The experimental findings demonstrated that the highest percentage of MO dye removal was achieved under the conditions of pH 2.0, a temperature of 60 °C, agitation speed of 250 rpm, and adsorption duration of 90 min. These Schiff bases were subsequently characterized using advanced analytical techniques including Fourier Transform Infrared spectroscopy, Thermal analysis (TGA and DSC), and Scanning Electron Microscopy.

Developing a new multi-featured chitosan-quinoline Schiff base with potent antibacterial, antioxidant, and antidiabetic activities: design and molecular modeling simulation.

A new chitosan Schiff base was developed via the reaction of chitosan (CH) with 2-chloro-3-formyl-7-ethoxy quinoline (Q) derivative. The alteration in the chemical structure and morphology of CHQ derivative was confirmed by 1H NMR, FT-IR spectroscopy and SEM analysis. The antibacterial activity was considerably promoted with increasing quinoline concentration up to 1 M with maximal inhibition reached 96 and 77% against Staphylococcus haemolyticus and Escherichia coli, respectively. Additionally, CHQ derivative afforded higher ABTS·+ radical scavenging activity reached 59% compared to 13% for native chitosan, approving its acceptable antioxidant activity. Moreover, the developed CHQ derivative can stimulate the glucose uptake in HepG-2 and yeast cells, while better inhibition of α-amylase and α-glucosidase was accomplished with maximum values of 99.78 and 92.10%, respectively. Furthermore, the molecular docking simulation clarified the binding mode of CHQ derivative inside the active site of α-amylase and α-glucosidase, suggesting its potential use as diabetes mellitus drug. The DFT calculations indicated an improvement in the electronic properties of CHQ with a lower energy band gap reached 4.05eV compared to 5.94eV for CH. The cytotoxicity assay revealed the safety of CHQ towards normal HSF cells, hypothesizing its possible application as non-toxic antibacterial, antioxidant, and antidiabetic agent for biomedical applications.

Graphene oxide@Fe3O4-decorated iota-carrageenan composite for ultra-fast and highly efficient adsorption of lead (II) from water.

The aggravated problem of lead pollution, especially in aquatic environments, necessitates the development of eminent adsorbents that could radically solve this environmental problem. Hence, a new composite was constructed based on iota carrageenan (i.Carr), graphene oxide (GO) and magnetite (Fe3O4) for removing noxious Pb2+ ions. The GO@Fe3O4-i.Carr composite was characterized by VSM, SEM, XPS, XRD, FTIR and Zeta potential. The removal of Pb2+ ions attained a quick equilibrium of almost 30 min with a removal efficiency reaching 93.68 %. The removal of Pb2+ was boosted significantly, in the order of GO@Fe3O4-i.Carr(1:1) > GO@Fe3O4-i.Carr(1:3) > GO@Fe3O4-i.Carr(3:1). Moreover, acquired experimental data fitted the pseudo 2nd order kinetic model and Freundlich isotherm model with a maximal monolayer adsorption capacity reached 440.05 mg/g. Notably, after five adsorption runs, the composite maintained its removal efficiency exceeding 74 %. The assumed adsorption mechanisms of Pb2+ onto GO@Fe3O4-i.Carr were complexation, precipitation, Lewis acid-base, and electrostatic attraction forces. Overall, the GO@Fe3O4-i.Carr composite elucidated the auspicious adsorbent criteria, comprising fast adsorption with high performance, ease-separation and tolerable recyclability, advising its feasible use to decontaminate water bodies from hazardous heavy metals.

Fabrication of Antibacterial and Antioxidant ZnO-Impregnated Amine-Functionalized Chitosan Bio-Nanocomposite Membrane for Advanced Biomedical Applications.

Developing a variety of safe and effective functioning wound dressings is a never-ending objective. Due to their exceptional antibacterial activity, biocompatibility, biodegradability, and healing-promoting properties, functionalized chitosan nanocomposites have attracted considerable attention in wound dressing applications. Herein, a novel bio-nanocomposite membrane with a variety of bio-characteristics was created through the incorporation of zinc oxide nanoparticles (ZnONPs) into amine-functionalized chitosan membrane (Am-CS). The developed ZnO@Am-CS bio-nanocomposite membrane was characterized by various analysis tools. Compared to pristine Am-CS, the developed ZnO@Am-CS membrane revealed higher water uptake and adequate mechanical properties. Moreover, increasing the ZnONP content from 0.025 to 0.1% had a positive impact on antibacterial activity against Gram-positive and Gram-negative bacteria. A maximum inhibition of 89.4% was recorded against Escherichia coli, with a maximum inhibition zone of 38 ± 0.17 mm, and was achieved by the ZnO (0.1%)@Am-CS membrane compared to 72.5% and 28 ± 0.23 mm achieved by the native Am-CS membrane. Furthermore, the bio-nanocomposite membrane demonstrated acceptable antioxidant activity, with a maximum radical scavenging value of 46%. In addition, the bio-nanocomposite membrane showed better biocompatibility and reliable biodegradability, while the cytotoxicity assessment emphasized its safety towards normal cells, with the cell viability reaching 95.7%, suggesting its potential use for advanced wound dressing applications.

Electrospun cellulose acetate/activated carbon composite modified by EDTA (rC/AC-EDTA) for efficient methylene blue dye removal.

The present study fabricated regenerated cellulose nanofiber incorporated with activated carbon and functionalized rC/AC3.7 with EDTA reagent for methylene blue (MB) dye removal. The rC/AC3.7 was fabricated by electrospinning cellulose acetate (CA) with activated carbon (AC) solution followed by deacetylation. FT-IR spectroscopy was applied to prove the chemical structures. In contrast, BET, SEM, TGA and DSC analyses were applied to study the fiber diameter and structure morphology, the thermal properties and the surface properties of rC/AC3.7-EDTA. The CA was successfully deacetylated to give regenerated cellulose nanofiber/activated carbon, and then ethylenediaminetetraacetic acid dianhydride was used to functionalize the fabricated nanofiber composite. The rC/AC3.7-EDTA, rC/AC5.5-EDTA and rC/AC6.7-EDTA were tested for adsorption of MB dye with maximum removal percentages reaching 97.48, 90.44 and 94.17%, respectively. The best circumstances for batch absorption experiments of MB dye on rC/AC3.7-EDTA were pH 7, an adsorbent dose of 2 g/L, and a starting MB dye concentration of 20 mg/L for 180 min of contact time, with a maximum removal percentage of 99.14%. The best-fit isotherm models are Temkin and Hasely. The outcome of isotherm models illustrates the applicability of the Langmuir isotherm model (LIM). The maximal monolayer capacity Qm determined from the linear LIM is 60.61 for 0.5 g/L of rC/AC3.7-EDTA. However, based on the results from error function studies, the generalized isotherm model has the lowest accuracy. The data obtained by the kinetic models' studies exposed that the absorption system follows the pseudo-second-order kinetic model (PSOM) throughout the absorption period.

Construction of efficient Ni-FeLDH@MWCNT@Cellulose acetate floatable microbeads for Cr(VI) removal: Performance and mechanism.

Water pollution is an aggravating dilemma that is extending around the world, threatening human survival. Strikingly, the notorious heavy metals like hexavalent chromium ions (Cr6+) cause environmental problems raising awareness of the essentials for finding feasible solutions. For this purpose, the self-floating Ni-FeLDH@MWCNT@CA microbeads were prepared for removing Cr6+. The morphological, thermal, and composition characteristics of Ni-FeLDH@MWCNT@CA microbeads were analyzed using XRD, FTIR, TGA, SEM, XPS, and zeta potential. Notably, the adsorption aptitude of Cr6+ was enhanced by raising the MWCNTs proportion to 5 wt% in microbeads. The Cr6+ adsorption onto Ni-FeLDH@MWCNT@CA fitted Langmuir and Freundlich isotherm models with qm of 384.62 mg/g at pH 3 and 298 K. The adsorption process was described kinetically by the pseudo-2nd order model. More importantly, the adsorption of Cr6+ onto Ni-FeLDH@MWCNT@CA occurred via electrostatic interactions, inner/outer sphere complexations, ion exchange, and reduction mechanisms. Besides, the cycling test showed the remarkable reusability of Ni-FeLDH@MWCNT@CA floatable microbeads for five subsequent cycles. The self-floating Ni-FeLDH@MWCNT@CA microbeads in this work provide essential support for the potential applications for the remediation of heavy metals-containing wastewater.

Carbohydrate ligands-directed active tumor targeting of combinatorial chemotherapy/phototherapy-based nanomedicine: A review.

Phototherapies or light mediated therapies, including mutually photothermal and photodynamic therapy that encompass irradiation of the target organs with light, have been widely employed as minimally invasive approach associated with negligible drug resistance for eradicating multiple tumors with minimal hazards to normal organs. Despite all these advantages, many obstacles in phototherapy hinder progress toward clinical application. Therefore, researchers have developed nano-particulate delivery systems integrated with phototherapy and therapeutic cytotoxic drugs to overcome these obstacles and achieve maximum efficacy in cancer treatment. Active targeting ligands were integrated into their surfaces to improve the selectivity and tumor targeting ability, enabling easy binding and recognition by cellular receptors overexpressed on the tumor tissue compared to normal ones. This enhances intratumoral accumulation with minimal toxicity on the adjacent normal cells. Various active targeting ligands, including antibodies, aptamers, peptides, lactoferrin, folic acid and carbohydrates, have been explored for the targeted delivery of chemotherapy/phototherapy-based nanomedicine. Among these ligands, carbohydrates have been applied due to their unique features that ameliorate the bioadhesive, noncovalent conjugation to biological tissues. In this review, the up-to-date techniques of employing carbohydrates active targeting ligands will be highlighted concerning the surface modification of the nanoparticles for ameliorating the targeting ability of the chemo/phototherapy.

Adsorption of nitrophenol onto a novel Fe3O4-κ-carrageenan/MIL-125(Ti) composite: process optimization, isotherms, kinetics, and mechanism.

Water pollution is a dreadful affair that has incessantly aggravated, exposing our planet to danger. In particular, the persistent nitro aromatic compound like nitrophenols causes anxiety to the researchers due to their hazardous impacts, excessive usage, and removal difficulty. For this purpose, a novel multi-featured composite was constructed based on κ-Carrageenan (κ-Carr), MOF (MIL-125(Ti)), and magnetic Fe3O4 for efficient adsorptive removal of o-nitrophenol (o-NP). Interestingly, BET measurements revealed the high surface area of Fe3O4-κ-Carr/MIL-125(Ti) of about 163.27 m2/g, while VSM showed its excellent magnetic property (20.34 emu/g). The comparison study pointed out the synergistic effect between Fe3O4, κ-Carr, and MIL-125(Ti), forming a composite with an excellent adsorption performance toward o-NP. The adsorption data obeyed pseudo-second-order kinetic model, and Freundlich isotherm model was better fitted than Langmuir and Temkin. Furthermore, Langmuir verified the supreme adsorption capacity of o-NP onto Fe3O4-κ-Carr/MIL-125(Ti) since the computed qmax reached 320.26 mg/g at pH 6 and 25 °C. Furthermore, the XPS results postulated that the adsorption mechanism pf o-NP proceeded via H-bonding, π-π interaction, and electron donor-acceptor interactions. Interestingly, Fe3O4-κ-Carr/MIL-125(Ti) composite retained good adsorption characteristics after reusing for five cycles, suggesting its viable applicability as an efficient, renewable, and easy-separable adsorbent for removing nitro aromatic pollutants.

Therapeutic potential of two formulated novel chitosan derivatives with prominent antimicrobial activities against virulent microorganisms and safe profiles toward fibroblast cells.

The development of new antimicrobial agents has been drawing considerable attention due to the extreme escalation of multi-drug resistant microorganisms. We thus sought to ameliorate the antimicrobial activities of the chitosan (Cs) biopolymer by coupling chitosan with cyclohexanone and 2-N-methyl pyrrolidone, synthesizing two novel Schiff bases (CsSB1 and CsSB2), respectively. FT-IR, TGA, DSC, SEM, and potentiometric titration were employed to characterize the formulated chitosan derivatives. The findings exposed that the degrees of deacetylation were 88.12% and 89.98% for CsSB1 and CsSB2, respectively. The antimicrobial capacities of CsSB1 and CsSB2 were substantially enhanced compared with prime chitosan. Furthermore, the CsSB1 and CsSB2 demonstrated minimum inhibitory concentrations (MIC) of 50 µg/ml in relation to all studied microorganisms, whereas chitosan revealed MIC value of 50 µg/ml only for E. coli. Furthermore, CsSB1 with a concentration of 250 µg/ml manifested the highest antibacterial activity against Gram-positive bacteria. Correspondingly, CsSB2 revealed a comparable trend of microbial hindrance with lower activities. Besides, the two derivatives could thwart the growth of Candida albicans (C. albicans). The cytotoxicity assay of the biomaterials accentuated their biocompatibility with fibroblasts. Collectively, the two formulated chitosan derivatives could competently rival the native chitosan, particularly for future applications in wound healing.

Composite nanofiber formation using a mixture of cellulose acetate and activated carbon for oil spill treatment.

Oil and organic pollutants are significant disasters affecting the aquatic ecosystem and human health. A novel nanofiber composite from cellulose acetate/activated carbon (CA/AC) was successfully fabricated by the electrospinning technique. CA/AC nanofiber composites were prepared from 10% (w/v) polymer solutions dissolving in DMA/acetone ratio 1:3 (v/v) with adding three different percentages of AC (3.7, 5.5, and 6.7%) to the total weight of CA. The prepared CA/AC nanofiber composite morphology reveals randomly oriented bead-free fibers with submicron fiber diameter. CA/AC nanofiber composites were further characterized by TGA, DSC, and surface area analysis. Water uptake was investigated for fabricated fibers at different pH. Oil adsorption was conducted in both static (oil only) and dynamic (oil/water) systems to estimate the adsorption capacity of prepared composites to treat heavy and light machine oils. The results showed increased oil adsorption capacity incorporating activated carbon into CA nanofiber mats. The maximum sorption capacity reached 8.3 and 5.5 g/g for heavy and light machine oils obtained by CA/AC5.5 (AC, 5.5%). A higher oil uptake was reported for the CA/AC composite nanofibers and showed a constant sorption capacity after the second recycles in the reusability test. Of isotherm models, the most applicable model was the Freundlich isotherm model. The result of kinetic models proved the fit of the pseudo-second-order kinetic model to the adsorption system.

Development of Azo Dye Immobilized Sulfonated Poly (Glycidyl Methacrylate) Polymer Composite as Novel Adsorbents for Water Treatment Applications: Methylene Blue Immobilization Isotherm, Kinetic, Thermodynamic, and Simulations Studies.

Methylene blue (MB) immobilized onto a sulfonated poly(glycidyl methacrylate) (SPGMA) polymer composite has been developed as a novel adsorbent for water treatment applications. The MB adsorptions onto sulfonated poly(glycidyl methacrylate) polymer characters have been studied. The adsorption isotherms, namely Langmuir and Freundlich, have been investigated. Other isotherm models. As a compromise between the Freundlich and Langmuir isotherm models, such as the D-R isotherm and the Temkin isotherm, have been compared. The results indicated that the adsorption process followed the Freundlich isotherm model, indicating heterogeneous surface site energies and multi-layer levels of sorption. This study selected three linear kinetic models, namely pseudo-first order, pseudo-second order, and Elovich, to describe the MB sorption process using SPGMA negatively charged nanoparticles (430 nm). The obtained data revealed that the adsorption process obeyed the pseudo-second-order kinetic model, suggesting that the rate-limiting step in these sorption processes may be chemisorption. Furthermore, the thermodynamic parameters have been evaluated. Moreover, the interaction of the MB molecules with SPGMA nanoparticles has been simulated using the governing equation that describes ion exchange resin derived from Nernst-Plank equations between two ion species. Finally, the developed MB-SPGMA composite adsorbent (27 mg/g) wastested for the first time for the removal of Cr6+ ions and Mn7+ metal ions from dichromate and permanganate-contaminated waters under mild adsorption conditions, opening a new field of multiuse of the same adsorbent in the removal of more than one contaminant.

Development of Azo Dye Immobilized Poly (Glycidyl Methacrylate-Co-Methyl Methacrylate) Polymers Composites as Novel Adsorbents for Water Treatment Applications: Methylene Blue-Polymers Composites.

Methylene blue azo dye (MB) immobilized onto Poly (glycidyl methacrylate-Co-methyl methacrylate), (PGMA-co-PMMA), and sulphonated Poly (glycidyl methacrylate-Co-methyl methacrylate), (SPGMA-co-PMMA), polymers composites have been developed as novel adsorbents for water treatment applications. The effect of copolymer composition and sulphonation on the MB content has been studied. Maximum MB content was correlated to the Polyglycidyl methacrylate content for both native and sulphonated copolymers. Furthermore, the effect of the adsorption conditions on the MB content was studied. Sulfonated Poly (glycidyl methacrylate; SPGMA) was the most efficient formed composite with the highest MB content. The developed composites' chemical structure and morphology were characterized using characterization tools such as particle size, FTIR, TGA, and SEM analyses. The developed MB-SPGMA composite adsorbent (27 mg/g), for the first time, was tested for the removal of Cr (VI) ions and Mn (VII) metal ions from dichromate and permanganate contaminated waters under mild adsorption conditions, opening a new field of multiuse of the same adsorbent in the removal of more than one contaminants.

Efficient removal of noxious methylene blue and crystal violet dyes at neutral conditions by reusable montmorillonite/NiFe2O4@amine-functionalized chitosan composite.

The jeopardy of the synthetic dyes effluents on human health and the environment has swiftly aggravated, threatening human survival. Hence, sustained studies have figured out the most acceptable way to eliminate this poisonous contaminant. Thereby, our investigation aimed to fabricate montmorillonite/magnetic NiFe2O4@amine-functionalized chitosan (MMT-mAmCs) composite as a promising green adsorbent to remove the cationic methylene blue (MB) and crystal violet (CV) dyes from the wastewater in neutral conditions. Interestingly, MMT-mAmCs composite carries high negative charges at a wide pH range from 4 to 11 as clarified from zeta potential measurements, asserting its suitability to adsorb the cationic contaminants. In addition, the experimental study confirmed that the optimum pH to adsorb both MB and CV was pH 7, inferring the ability of MMT-mAmCs to adsorb both cationic dyes in simple process conditions. Furthermore, the ferromagnetic behavior of the MMT-mAmCs composite is additional merit to our adsorbent that provides facile, fast, and flawless separation. Notably, the as-fabricated composite revealed an auspicious adsorbability towards the adsorptive removal of MB and CV, since the maximum adsorption capacity of MB and CV were 137 and 118 mg/g, respectively. Moreover, the isotherm and kinetic investigatins depicted that the adsorption of both cationic dyes fitted Langmuir and Pseudo 2nd order models, respectively. Besides, the advanced adsorbent preserved satisfactory adsorption characteristics with maximal removal efficacy exceeding 87% after reuse for ten consecutive cycles. More importantly, MMT-mAmCs efficiently adsorbed MB and CV from real agricultural water, Nile river water and wastewater samples at the neutral pH medium, reflecting its potentiality to be a superb reusable candidate for adsorptive removal cationic pollutants from their aquatic media.

Reusable kaolin impregnated aminated chitosan composite beads for efficient removal of Congo red dye: isotherms, kinetics and thermodynamics studies.

In this investigation, Kaolin (K) impregnated aminated chitosan (AM-CTS) composite beads were fabricated with multi-features including low-cost, high performance, renewable and ease of separation for adsorption of anionic Congo red (CR) dye. Characterization tools such as FTIR, XRD, SEM, TGA, BET, XPS and Zeta potential were thoroughly employed to confirm the successful formulation process. The results revealed that K@ AM-CTS composite beads displayed higher specific surface area (128.52 m2/g), while the thermal stability was prominently improved compared to pure AM-CTS. In addition, the adsorption equilibrium of CR dye was accomplished rapidly and closely gotten within 45 min. The removal efficiency was significantly enriched and reached 90.7% with increasing kaolin content up to 0.75%, compared to 20.3 and 58% for pristine kaolin and AM-CTS, respectively. Moreover, the adsorption process obeyed the pseudo-first order kinetic model, while data were agreed with the Freundlich isotherm model with a maximum adsorption capacity reached 104 mg/g at pH 6. Furthermore, D-R isotherm model demonstrated the physical adsorption process of CR dye, which includes the electrostatic interactions, ion exchange and H-bonding. Thermodynamics evidenced the spontaneous and endothermic nature of the adsorption process. Interestingly, the developed K@AM-CTS composites beads showed better reusability for eight consecutive cycles, suggesting their feasible applicability for adsorptive removal anionic dyes from polluted aquatic bodies.

Sulfonated graphene oxide impregnated cellulose acetate floated beads for adsorption of methylene blue dye: optimization using response surface methodology.

New multi-featured adsorbent beads were fabricated through impregnation of sulfonated graphene (SGO) oxide into cellulose acetate (CA) beads for fast adsorption of cationic methylene blue (MB) dye. The formulated SGO@CA composite beads were thoroughly characterized by several tools including FTIR, TGA, SEM, XRD, XPS and zeta potential. The optimal levels of the most significant identified variables affecting the adsorption process were sequential determined by the response surface methodology (RSM) using Plackett-Burman and Box-Behnken designs. The gained results denoted that the surface of SGO@CA beads displayed the higher negative charges (- 42.2 mV) compared to - 35.7 and - 38.7 mV for pristine CA and SGO, respectively. In addition, the floated SGO@CA beads demonstrated excellent floating property, fast adsorption and easy separation. The adsorption performance was accomplished rapidly, since the adsorption equilibrium was closely gotten within 30 min. Furthermore, the adsorption capacity was greatly improved with increasing SGO content from 10 to 30%. The obtained data were followed the pseudo-second order kinetic model and agreed with Langmuir adsorption isotherm model with a maximum adsorption capacity reached 234.74 mg g-1. The thermodynamic studies designated the spontaneity and endothermic nature of MB dye adsorption. Besides, the floated beads exposed acceptable adsorption characteristics for six successive reuse cycles, in addition to their better adsorption selectivity towards MB dye compared to cationic crystal violet and anionic Congo red dyes. These findings assume that the formulated SGO@CA floated beads could be used effectively as highly efficient, easy separable and reusable adsorbents for the fast removal of toxic cationic dyes.

Novel reusable amine-functionalized cellulose acetate beads impregnated aminated graphene oxide for adsorptive removal of hexavalent chromium ions.

In this study, a multi-featured adsorbent was developed for the adsorptive removal of hexavalent chromium (Cr6+) ions. Herein, aminated graphene oxide (GO-NH2) was firstly synthetized and incorporated into cellulose acetate beads (CA) which were followed by surface amine-functionalization process. Varies characterization tools such as FT-IR spectroscopy, SEM, TGA, XRD, BET, XPS and zeta potential were employed to ensure the successful fabrication of GO-NH2@CA-NH2 composite beads. An enhancement in the adsorption performance was attained, while the adsorption equilibrium was closely gotten within only 60 min. Therefore, the adsorption capacity was boosted with increasing GO-NH2 ratio in the beads matrix from 10 to 25%. Furthermore, the adsorption process agreed with Freundlich isotherm model with a supreme adsorption capacity of 410.21 mg/g at pH 2, while data followed the pseudo-second-order kinetic model. Besides, thermodynamic studies denoted that the adsorption process was endothermic, randomness and spontaneous. The composite beads retained better adsorption characteristics for seven sequential cycles with ease of separation. The proposed adsorption of Cr6+ onto GO-NH2@CA-NH2 surface occurred via the electrostatic interactions, reduction process and coordinate-covalent bonds. These findings hypothesize that the fabricated GO-NH2@CA-NH2 beads could be act as easy-separable and reusable adsorbent for efficient adsorption of Cr6+ ions.

Recent developments in alginate-based adsorbents for removing phosphate ions from wastewater: a review.

The huge development of the industrial sector has resulted in the release of large quantities of phosphate anions which adversely affect the environment, human health, and aquatic ecosystems. Naturally occurring biopolymers have attracted considerable attention as efficient adsorbents for phosphate anions due to their biocompatibility, biodegradability, environmentally-friendly nature, low-cost production, availability in nature, and ease of modification. Amongst them, alginate-based adsorbents are considered one of the most effective adsorbents for removing various types of pollutants from industrial wastewater. The presence of active COOH and OH- groups along the alginate backbone facilitate its physical and chemical modifications and participate in various possible adsorption mechanisms of phosphate anions. Herein, we focus our attention on presenting a comprehensive overview of recent advances in phosphate removal by alginate-based adsorbents. Modification of alginate by various materials, including clays, magnetic materials, layered double hydroxides, carbon materials, and multivalent metals, is addressed. The adsorption potentials of these modified forms for removing phosphate anions, in addition to their adsorption mechanisms are clearly discussed. It is concluded that ion exchange, complexation, precipitation, Lewis acid-base interaction and electrostatic interaction are the most common adsorption mechanisms of phosphate removal by alginate-based adsorbents. Pseudo-2nd order and Freundlich isotherms were figured out to be the major kinetic and isotherm models for the removal process of phosphate. The research findings revealed that some issues, including the high cost of production, leaching, and low efficiency of recyclability of alginate-based adsorbents still need to be resolved. Future trends that could inspire further studies to find the best solutions for removing phosphate anions from aquatic systems are also elaborated, such as the synthesis of magnetic-based alginate and various-shaped alginate nanocomposites that are capable of preventing the leaching of the active materials.